Toyota Avalon (XX50): Rear Crankshaft Oil Seal

*1

REAR ENGINE OIL SEAL

*2

NO. 1 CRANKSHAFT POSITION SENSOR PLATE

*3

DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

*4

REAR DRIVE PLATE SPACER

N*m (kgf*cm, ft.*lbf): Specified torque

●

Non-reusable part

MP grease

Adhesive 1324

★

Precoated part

-

-

(b) Apply MP grease to the lip of a new rear engine oil seal.

NOTICE:

• Keep the lip free from foreign matter.
• Do not tap in the rear engine oil seal at an angle.

(a) Install the No. 1 crankshaft position sensor plate.

HINT:

Align the pin of the No. 1 crankshaft position sensor plate with the pin hole of the crankshaft.

(a) Using SST, hold the crankshaft pulley.

SST: 09213-70011

09213-70020

SST: 09330-00021

*1

Drive Plate and Ring Gear Sub-assembly

*2

Rear Drive Plate Spacer

Transaxle Side

(d) Apply adhesive to 2 or 3 threads at the end of each of the 8 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

(e) Install and uniformly tighten the 8 bolts in several steps in the sequence shown in the illustration.

Torque:

83 N·m {846 kgf·cm, 61 ft·lbf}

NOTICE:

Do not start the engine for at least 1 hour after installing the drive plate and ring gear sub-assembly.

Battery terminal is disconnected/reconnected

Perform steering sensor zero point calibration

Lane departure alert system (w/ Steering Control)

Pre-collision system

Intelligent Clearance Sonar System*1

Lighting System (for Gasoline Model with Cornering Light)

Memorize steering angle neutral point

Parking Assist Monitor System

Panoramic View Monitor System

Replacement of ECM

Vehicle Identification Number (VIN) registration

MIL comes on

ECU communication ID registration (Immobiliser system)

Engine start function

Gas leak from exhaust system is repaired

Inspection after repair

• Poor idle, etc.
• Engine start function, etc.

Replacement of automatic transaxle assembly

• Perform reset memory
• Input transaxle compensation code into ECM
• Perform road test to allow ECM to learn

• Large shift shock
• Deterioration of fuel efficiency

for Initialization

for Registration

Replacement of ECM

(If transaxle compensation code read from ECM)

• Perform reset memory*2
• Transfer transaxle compensation code
• Perform road test to allow ECM to learn

Replacement of ECM

(If transaxle compensation code not read from ECM)

• Perform reset memory*2
• Reset transaxle compensation code
• Perform road test to allow ECM to learn

Replacement of automatic transaxle fluid

ATF thermal degradation estimate reset

The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly

Replacement of ECM

Code registration (Smart Key System (for Start Function))

• Wireless Door Lock Control System
• Smart Key System (for Entry Function)
• Smart Key System (for Start Function)
• Steering lock function

Suspension, tires, etc.

• Measure ultrasonic sensor detection angle
• Ultrasonic sensor detection angle registration

• Intelligent Clearance Sonar System
• Intuitive Parking Assist System

Rear television camera assembly optical axis adjustment (Back camera position setting)

Parking Assist Monitor System

for Initialization

for Calibration

• Parking assist ECU initialization
• Adjust steering angle
• Television camera assembly optical axis adjustment (Back camera position setting)

Panoramic View Monitor System

for Initialization

for Calibration

Perform headlight ECU sub-assembly LH initialization

Lighting system (for Gasoline Model with Cornering Light)

Front wheel alignment adjustment

Perform system variant learning and acceleration sensor zero point calibration.

• VSC is disabled or malfunctions
• DTCs are output
• Slip indicator light illuminates
• ABS warning light illuminates

(b) Using SST, hold the crankshaft pulley.

SST: 09213-70011

09213-70020

SST: 09330-00021

(c) Remove the 8 bolts, the rear drive plate spacer, the drive plate and ring gear sub-assembly.

(a) Using a knife, cut through the lip of the rear engine oil seal.